My Cart

    • The product Disposable ECG Electrode (10 Pcs pack) has been added to comparison list.

XBee ZB SMA Module

35 €35.00

Availability: Retired

XBee ZB embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. SMA-RP Version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Description

XBee ZB embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. SMA-RP Version.

Performance

RF Data Rate 250 Kbps
Indoor/Urban Range 133 ft (40 m)
Outdoor/RF Line-of-Sight Range  
400 ft (120 m)
Transmit Power 1.25 mW (+1 dBm) / 2 mW (+3 dBm) boost mode
Receiver Sensitivity (1% PER) -96 dBm in boost mode

Features

Adjustable Power Yes
I/O Interface 3.3V CMOS UART, ADC, DIO
Configuration Method API or AT commands, local or over-the-air
Frequency Band 2.4 GHz
Interference Immunity DSSS (Direct Sequence Spread Spectrum)
Serial Data Rate 1200 bps - 1 Mbps
ADC Inputs (4) 10-bit ADC inputs
Digital I/O 10
Antenna Options Chip, Wire Whip, U.FL, RPSMA
Operating Temperature
& Humidity
-40° C to +85° C, 0-95% humidity non-condensing

Programmability

Networking & Security
Encryption 128-bit AES
Reliable Packet Delivery Retries/Acknowledgments
IDs and Channels PAN ID, 64-bit IEEE MAC, 16 channels

Power Requirements

Supply Voltage 2.1 - 3.6VDC
Transmit Current 35 mA / 45 mA boost mode @ 3.3VDC
Receive Current 38 mA / 40 mA boost mode @ 3.3VDC
Power-Down Current <1 uA @ 25º C

Regulatory Approvals

FCC (USA) Yes
IC (Canada) Yes
ETSI (Europe) Yes
C-TICK (Australia) Yes
TELEC (Japan) Yes

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Related Tutorials

The Arduino XBee shield allows your Arduino board to communicate wirelessly using Zigbee. It was developed in collaboration with Arduino. This documentation describes the use of the shield with the XBee module.

It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to turn ON and OFF a RGB LED with different colors depending on data sent by XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to measure the amount light in a room and print it in a graph. This data is sent to a XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to move a servo to different degrees depending on the data sent by the XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to set a password key and if it is correct, a LED and a Buzzer will sound printing a message in the LCD.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

The Multiprotocol Radio Shield is an interconnection shield for Arduino, and was designed to connect two communication modules at the same time. This that means a lot of possibilities and applications can be made using the cooking-hacks modules.

The Multiprotocol Radio Shield includes the SPI bus connections that allows the use of the RS-485 and CAN Bus modules, but also is compatible with the rest of the cooking-hacks modules as RFID, XBee and Bluetooth.

The current tutorial explains how to take the most of the Galileo board by using on it the Arduino and Raspberry Pi shields and modules designed by Cooking Hacks

Galileo comes with a single-core 32-bit, 400MHz Quark SoC X1000 processor, supports 3.3 or 5 volt shields and has an Ethernet and USB port. Compatible with Windows, Mac OS and Linux, the software of Galileo also has support for the Arduino shield ecosystem.

The idea behind the Raspberry Pi to Arduino shields connection bridge is to allow to use any of the shields, boards and modules designed for Arduino in Raspberry Pi.

It includes also the possibility of connecting digital and analog sensors, using the same pinout of Arduino but with the power and capabilities of Raspberry.

If you are interested in Internet of Things (IoT) or M2M projects check our open source sensor platform Waspmote which counts with more than 100 sensors available to use 'off the shelf', a complete API with hundreds of ready to use codes and a low consumption mode of just 0.7µA to ensure years of battery life.

Know more at:

Get the Starter Kits at: