My Cart

Xbee Pro IEEE 802.15.4 2.4Ghz 63mW 250Kbps RF Module w/ U.FL

81.75 €81.75

Availability: Retired

XBee-PRO 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing.   XBee-PRO modules are power-amplified versions of XBee modules for extended-range applications. Part of the XBee family of RF products, these modules are easy-to-use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. Module users have the ability to substitute one XBee module for another with minimal development time and risk.   Features: No configuration needed for out-of-the-box RF communications Common XBee footprint for a variety of RF modules Fast 250 kbps RF data rate to the end node 2.4 GHz for worldwide deployment Sleep modes supported for extended battery life   Specification? Power output: 63 mW (+18 dBm) North American version ,10 mW (+10 dBm) International version Indoor/Urban range: Up to 300 ft (90 m) Outdoor/RF line-of-sight range: Up to 1 mile (1.6 km) RF LOS Receiver sensitivity: -100 dBm (all variants) RF data rate: 250 Kbps Operating frequency: 2.4 GHz Interface data rate: Up to 115.2 Kbps   Networking: Spread spectrum typ: DSSS (Direct Sequence Spread Spectrum) Supported network topologies: Point-to-point, point-to-multipoint, & peer-to-peer Error handling: Retries & acknowledgements Filtration options: PAN ID, Channel, and 64-bit addresses Channel capacity: 12 Channels Addressing: 65,000 network addresses available for each channel   Power: Supply voltage: 2.8 - 3.4 VDC,XBee Footprint Recommendation: 3.0 - 3.4 VDC Transmit current: 215 mA (@ 3.3 V) Receive current : 55 mA (@ 3.3 V) Power-down sleep current: <10 µA at 25° C   General: Frequency band: 2.4000 - 2.4835 GHz Interface options: 3V CMOS UART

Description

XBee-PRO 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing.   XBee-PRO modules are power-amplified versions of XBee modules for extended-range applications. Part of the XBee family of RF products, these modules are easy-to-use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. Module users have the ability to substitute one XBee module for another with minimal development time and risk.   Features: No configuration needed for out-of-the-box RF communications Common XBee footprint for a variety of RF modules Fast 250 kbps RF data rate to the end node 2.4 GHz for worldwide deployment Sleep modes supported for extended battery life   Specification? Power output: 63 mW (+18 dBm) North American version ,10 mW (+10 dBm) International version Indoor/Urban range: Up to 300 ft (90 m) Outdoor/RF line-of-sight range: Up to 1 mile (1.6 km) RF LOS Receiver sensitivity: -100 dBm (all variants) RF data rate: 250 Kbps Operating frequency: 2.4 GHz Interface data rate: Up to 115.2 Kbps   Networking: Spread spectrum typ: DSSS (Direct Sequence Spread Spectrum) Supported network topologies: Point-to-point, point-to-multipoint, & peer-to-peer Error handling: Retries & acknowledgements Filtration options: PAN ID, Channel, and 64-bit addresses Channel capacity: 12 Channels Addressing: 65,000 network addresses available for each channel   Power: Supply voltage: 2.8 - 3.4 VDC,XBee Footprint Recommendation: 3.0 - 3.4 VDC Transmit current: 215 mA (@ 3.3 V) Receive current : 55 mA (@ 3.3 V) Power-down sleep current: <10 µA at 25° C   General: Frequency band: 2.4000 - 2.4835 GHz Interface options: 3V CMOS UART

Related Tutorials

The Multiprotocol Radio Shield is an interconnection shield for Arduino, and was designed to connect two communication modules at the same time. This that means a lot of possibilities and applications can be made using the cooking-hacks modules.

The Multiprotocol Radio Shield includes the SPI bus connections that allows the use of the RS-485 and CAN Bus modules, but also is compatible with the rest of the cooking-hacks modules as RFID, XBee and Bluetooth.

The Arduino XBee shield allows your Arduino board to communicate wirelessly using Zigbee. It was developed in collaboration with Arduino. This documentation describes the use of the shield with the XBee module.

It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to measure the amount light in a room and print it in a graph. This data is sent to a XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to move a servo to different degrees depending on the data sent by the XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to set a password key and if it is correct, a LED and a Buzzer will sound printing a message in the LCD.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to turn ON and OFF a RGB LED with different colors depending on data sent by XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

If you are interested in Internet of Things (IoT) or M2M projects check our open source sensor platform Waspmote which counts with more than 100 sensors available to use 'off the shelf', a complete API with hundreds of ready to use codes and a low consumption mode of just 0.7µA to ensure years of battery life.

Know more at:

Get the Starter Kits at: