My Cart

XBee 868 MHz UFL Module + Pigtail

129 €129.00

Availability: In stock

XBee-PRO 868 modules are long-range embedded RF modules providing end-point device connectivity for European applications. Supporting RF line-of-sight distances up to 80 km, these modules are ideal for challenging wireless environments where RF penetration and transmission distance are critical to the application. Only for use in EUROPE.It includes a ufl to SMA pigtail to use with our 2dBi or 5dBi antennas.

  • 868 MHz short-range device G3 band for Europe
  • No configuration needed for out-of-the-box RF communications
  • Common XBee® footprint for a variety of RF modules
  • Outdoor RF line-of-sight range up to 80 km
  • Simple to use peer-to-peer or point-to-multipoint topology
  • Product datasheet

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Qty:
Add to Compare

Description

XBee-PRO 868 modules are long-range embedded RF modules providing end-point device connectivity for European applications. Supporting RF line-of-sight distances up to 80 km, these modules are ideal for challenging wireless environments where RF penetration and transmission distance are critical to the application. Only for use in EUROPE.It includes a ufl to SMA pigtail to use with our 2dBi or 5dBi antennas.

Performance
RF Data Rate 24 Kbps (limited to 10% duty cycle)
Indoor/Urban Range Up to 1800 ft (550 m)
Outdoor/RF Line-of-Sight Range Up to 25 miles (40 km) with dipole antenna
Up to 10 miles (16 km) with dipole antenna (13.7 dBm) - Italy only
Transmit Power 1 mW (0 dBm) to 315 mW (+25 dBm)
Receiver Sensitivity (1% PER) -112 dBm

Features

Serial Data Interface 3.3V CMOS Serial UART
Configuration Method API and AT commands
Frequency Band 868 MHz ISM
Interference Immunity Multiple transmissions, acknowledgements
Serial Data Rate 1.2 Kbps to 230.4 Kbps (nonstandard rates available)
ADC Inputs Coming in future firmware revisions
Digital I/O Coming in future firmware revisions

Networking & Security

Encryption 128-bit AES
Reliable Packet Delivery Retries/Acknowledgments
Addressing Options Network ID, 32-bit address
Channels Single channel

Power Requirements

Supply Voltage 3.0 – 3.6 VDC
Transmit Current 500 mA typical at 3.3V (800 mA max)
Receive Current 65 mA typical
Power-Down Current Coming in future firmware revisions

Regulatory Approvals

FCC (USA) No
IC (Canada) No
ETSI (Europe) Yes (Italy 25 mW max)
C-TICK (Australia) No
Telec (Japan) No

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Related Tutorials

The Multiprotocol Radio Shield is an interconnection shield for Arduino, and was designed to connect two communication modules at the same time. This that means a lot of possibilities and applications can be made using the cooking-hacks modules.

The Multiprotocol Radio Shield includes the SPI bus connections that allows the use of the RS-485 and CAN Bus modules, but also is compatible with the rest of the cooking-hacks modules as RFID, XBee and Bluetooth.

The Arduino XBee shield allows your Arduino board to communicate wirelessly using Zigbee. It was developed in collaboration with Arduino. This documentation describes the use of the shield with the XBee module.

It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to measure the amount light in a room and print it in a graph. This data is sent to a XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to move a servo to different degrees depending on the data sent by the XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to set a password key and if it is correct, a LED and a Buzzer will sound printing a message in the LCD.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to turn ON and OFF a RGB LED with different colors depending on data sent by XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

If you are interested in Internet of Things (IoT) or M2M projects check our open source sensor platform Waspmote which counts with more than 100 sensors available to use 'off the shelf', a complete API with hundreds of ready to use codes and a low consumption mode of just 0.7µA to ensure years of battery life.

Know more at:

Get the Starter Kits at: