My Cart

    • The product SparkFun Humidity and Temperature Sensor Breakout - SHT15 has been added to comparison list.

XBee 802.15.4 SMA Module

35 €35.00

Availability: Retired

XBee 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing. SMA-RP version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Description

XBee 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing. SMA-RP version.

Performance: XBee

  • Power output:: 1mW (+0 dBm) North American & International version
  • Indoor/Urban range: Up to 100 ft (30 m)
  • Outdoor/RF line-of-sight range: Up to 300 ft (90 m)
  • RF data rate: 250 Kbps
  • Interface data rate: Up to 115.2 Kbps
  • Operating frequency: 2.4 GHz
  • Receiver sensitivity: -92 dBm

Networking

  • Spread Spectrum type: DSSS (Direct Sequence Spread Spectrum)
  • Networking topology: Point-to-point, point-to-multipoint, & peer-to-peer
  • Error handling: Retries & acknowledgements
  • Filtration options: PAN ID, Channel, and 64-bit addresses
  • Channel capacity:
    • XBee: 16 Channels
  • Addressing: 65,000 network addresses available for each channel

Power

  • Supply voltage: 
    • XBee: 2.8 - 3.4 VDC
    • XBee Footprint Recommendation: 3.0 - 3.4 VDC
  • Transmit current:
    • XBee: 45 mA (@ 3.3 V) boost mode 35 mA (@ 3.3 V) normal mode
  • Receive current:
    • XBee: 50 mA (@ 3.3 V)
  • Power-down sleep current:
    • XBee: <10 µA at 25° C

General

  • Frequency band: 2.4000 - 2.4835 GHz
  • Interface options: 3V CMOS UART

Physical Properties

  • Size: 
    • XBee: 0.960 in x 1.087 in (2.438 cm x 2.761 cm)
  • Weight: 0.10 oz (3g)
  • Operating temperature: -40° C to 85° C (industrial)

Certifications

  • FCC: Yes
  • IC: Yes
  • Europe/ETSI: Yes
  • Australia/Ctick: Yes
  • RoHS: Compliant

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Related Tutorials

The Multiprotocol Radio Shield is an interconnection shield for Arduino, and was designed to connect two communication modules at the same time. This that means a lot of possibilities and applications can be made using the cooking-hacks modules.

The Multiprotocol Radio Shield includes the SPI bus connections that allows the use of the RS-485 and CAN Bus modules, but also is compatible with the rest of the cooking-hacks modules as RFID, XBee and Bluetooth.

The Arduino XBee shield allows your Arduino board to communicate wirelessly using Zigbee. It was developed in collaboration with Arduino. This documentation describes the use of the shield with the XBee module.

It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to measure the amount light in a room and print it in a graph. This data is sent to a XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to move a servo to different degrees depending on the data sent by the XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to set a password key and if it is correct, a LED and a Buzzer will sound printing a message in the LCD.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

This tutorial allows the user to turn ON and OFF a RGB LED with different colors depending on data sent by XBee gateway.

This project can be developed with Arduino or Intel Galileo. It is also compatible with Raspberry Pi using the Raspberry Pi to Arduino shields connection bridge.

If you are interested in Internet of Things (IoT) or M2M projects check our open source sensor platform Waspmote which counts with more than 100 sensors available to use 'off the shelf', a complete API with hundreds of ready to use codes and a low consumption mode of just 0.7µA to ensure years of battery life.

Know more at:

Get the Starter Kits at: