My Cart

WIZnet W5100 Network Module with Mag Jack - WIZ811MJ

25 €25.00

Availability: Retired

WIZnet's WIZ811MJ works as a breakout board for their W5100 embedded TCP/IP chip. Also included on the board is an RJ-45 MagJack connector (RJ45 with X’FMR). It can be used as a component and little effort is required to interface to the W5100. The WIZ811MJ is an ideal option for users who want a simple solution to adding TCP/IP capability to their project.

There is no on-board regulation, so you'll need to supply clean/regulated power sources. All pins of the W5100 are broken out to two pairs of 10-pin, 0.1" pitch headers.

For detailed information on implementation of Hardware TCP/IP, refer to the W5100 Datasheet.

Features:

  • Supports 10/100 Base TX
  • Supports half/full duplex operation
  • Supports auto-negotiation and auto cross-over detection
  • IEEE 802.3/802.3u Compliance
  • Operates 3.3V with 5V I/O signal tolerance
  • Supports network status indicator LEDs
  • Includes Hardware Internet protocols: TCP, IP Ver.4, UDP, ICMP, ARP, PPPoE, IGMP
  • Includes Hardware Ethernet protocols: DLC, MAC
  • Supports 4 independent connections simultaneously
  • Supports MCU bus Interface and SPI Interface
  • Supports Direct/Indirect mode bus access
  • Supports Socket API for easy application programming
  • Interfaces with two 2.54mm pitch 2 x 10 header pin
  • Temperature : 0 ~ 70℃ (Operation), -40 ~ 85℃ (Storage)

Dimensions:

  • Board: 55.5x25x23.5 (W x H x D)

Documents:



Description

WIZnet's WIZ811MJ works as a breakout board for their W5100 embedded TCP/IP chip. Also included on the board is an RJ-45 MagJack connector (RJ45 with X’FMR). It can be used as a component and little effort is required to interface to the W5100. The WIZ811MJ is an ideal option for users who want a simple solution to adding TCP/IP capability to their project.

There is no on-board regulation, so you'll need to supply clean/regulated power sources. All pins of the W5100 are broken out to two pairs of 10-pin, 0.1" pitch headers.

For detailed information on implementation of Hardware TCP/IP, refer to the W5100 Datasheet.

Features:

  • Supports 10/100 Base TX
  • Supports half/full duplex operation
  • Supports auto-negotiation and auto cross-over detection
  • IEEE 802.3/802.3u Compliance
  • Operates 3.3V with 5V I/O signal tolerance
  • Supports network status indicator LEDs
  • Includes Hardware Internet protocols: TCP, IP Ver.4, UDP, ICMP, ARP, PPPoE, IGMP
  • Includes Hardware Ethernet protocols: DLC, MAC
  • Supports 4 independent connections simultaneously
  • Supports MCU bus Interface and SPI Interface
  • Supports Direct/Indirect mode bus access
  • Supports Socket API for easy application programming
  • Interfaces with two 2.54mm pitch 2 x 10 header pin
  • Temperature : 0 ~ 70℃ (Operation), -40 ~ 85℃ (Storage)

Dimensions:

  • Board: 55.5x25x23.5 (W x H x D)

Documents:

If you are interested in Internet of Things (IoT) or M2M projects check our open source sensor platform Waspmote which counts with more than 100 sensors available to use 'off the shelf', a complete API with hundreds of ready to use codes and a low consumption mode of just 0.7µA to ensure years of battery life.

Know more at:

Get the Starter Kits at: