My Cart

Serial Port Programmer - ICSP Only

11 €11.00

Availability: Retired

PIC-PG1 is a programmer based on the JDM design which takes all necessary signals and power supply from RS232 serial port. It uses a 6 pin 0.1" step ICSP connector to connect to the target board. Simple, yet extremely useful. The PG1 works very well in conjunction with all Olimex PIC Development boards. It can also be used with bread boards utilizing a Polarized ICSP Header or with simple jumper wires.

Caution: The programmer may not work with low power serial interfaces - i.e. laptop or notebook serial ports. USB to serial cables have also not been proven to work.

Dimensions: 50x30 mm (1.3x2") + 30 cm (12") cable
Documents:

Tutorials: ICProg Setup and ICSP Setup

Software: ICPROG by Bonny Gijzen. It's the best software for serial port programmers we've seen - and it's free!

Supported Devices: Family followed by device type (Ex: 12C508, 16F84A)

12C: 508, 508A, 509, 509A, 671, 672
12CE: 518, 519, 673, 674
12F: 629, 675

16C: 433, 54, 56, 58, 61, 62A, 62B, 63, 63A, 64A, 65A, 65B, 66, 67, 71, 72, 72A, 73A, 73B, 74A, 74B, 76, 77, 505, 620, 620A, 621, 621A, 622, 622A, 710, 711, 712, 715, 716, 717, 745, 765, 770, 771, 773, 774, 781, 782, 923, 924
16CE: 623, 624, 625
16F: 83, 84, 84A, 627, 628, 630, 676, 818, 819, 870, 871, 872, 873, 873A, 874, 874A, 876, 876A, 877, 877A

18F: 242, 248, 252, 258, 442, 448, 452, 458, 1320, 2320, 4320, 4539, 6620, 6720, 8620, 8720

WinPic - Great new software by Wolfgang "Wolf" Bnscher. Supports all the popular flash PICs, as well as many of the newly released PICs! Use this software for support for the 16F628A, 16F87, and 16F88.

Supported Devices: Family followed by device type (Ex: 12F629, 16F84A)

12F: 629, 675

16C: 61, 71, 710, 711, 715
16F: 73, 74, 76, 77, 84, 627, 628, 628A, 818, 819, 870, 871, 872, 873, 873A, 874, 874A, 876, 876A, 877, 877A, 87, 88



Description

PIC-PG1 is a programmer based on the JDM design which takes all necessary signals and power supply from RS232 serial port. It uses a 6 pin 0.1" step ICSP connector to connect to the target board. Simple, yet extremely useful. The PG1 works very well in conjunction with all Olimex PIC Development boards. It can also be used with bread boards utilizing a Polarized ICSP Header or with simple jumper wires.

Caution: The programmer may not work with low power serial interfaces - i.e. laptop or notebook serial ports. USB to serial cables have also not been proven to work.

Dimensions: 50x30 mm (1.3x2") + 30 cm (12") cable
Documents:

Tutorials: ICProg Setup and ICSP Setup

Software: ICPROG by Bonny Gijzen. It's the best software for serial port programmers we've seen - and it's free!

Supported Devices: Family followed by device type (Ex: 12C508, 16F84A)

12C: 508, 508A, 509, 509A, 671, 672
12CE: 518, 519, 673, 674
12F: 629, 675

16C: 433, 54, 56, 58, 61, 62A, 62B, 63, 63A, 64A, 65A, 65B, 66, 67, 71, 72, 72A, 73A, 73B, 74A, 74B, 76, 77, 505, 620, 620A, 621, 621A, 622, 622A, 710, 711, 712, 715, 716, 717, 745, 765, 770, 771, 773, 774, 781, 782, 923, 924
16CE: 623, 624, 625
16F: 83, 84, 84A, 627, 628, 630, 676, 818, 819, 870, 871, 872, 873, 873A, 874, 874A, 876, 876A, 877, 877A

18F: 242, 248, 252, 258, 442, 448, 452, 458, 1320, 2320, 4320, 4539, 6620, 6720, 8620, 8720

WinPic - Great new software by Wolfgang "Wolf" Bnscher. Supports all the popular flash PICs, as well as many of the newly released PICs! Use this software for support for the 16F628A, 16F87, and 16F88.

Supported Devices: Family followed by device type (Ex: 12F629, 16F84A)

12F: 629, 675

16C: 61, 71, 710, 711, 715
16F: 73, 74, 76, 77, 84, 627, 628, 628A, 818, 819, 870, 871, 872, 873, 873A, 874, 874A, 876, 876A, 877, 877A, 87, 88

If you are interested in Internet of Things (IoT) or M2M projects check our open source sensor platform Waspmote which counts with more than 100 sensors available to use 'off the shelf', a complete API with hundreds of ready to use codes and a low consumption mode of just 0.7µA to ensure years of battery life.

Know more at:

Get the Starter Kits at: