My Cart

PowerSwitch Tail Kit

27.8 €27.80

Availability: Retired

Want to control a standard wall outlet device with your micro controller, but don’t want to mess with the high voltage wiring? This might just be the right device for you! The PowerSwitch Tail Kit is designed to allow you to safely control an outlet device without exposing any 120VAC voltages while being able to “customize” it to meet your applications needs. You can optimize the voltage required for the control signal by selecting and installing different resistor values for R1/R2 slots on the kit PCB. With this ability to choose the control signal voltage the PowerSwitch Tail Kit is given the ability to provide an input voltage from 3VDC all the way to 26VDC. Additionally, power cables are sold separately to give you the choice of cable you wish to use with this kit.This variation of the PowerSwitch Tail is sold as an easy-to-assemble kit and includes everything listed below with clear assembly instructions listed in the documents section.Includes:1x PowerSwitch Tail PCB1x PowerSwitch Tail Enclosure (w/ Case and PCB Screws)1x Relay (120VAC, 40A)1x Red LED (3mm)1x Metal Oxide Varistor 14mm (130V)1x Metal Oxide Varistor 7mm (130V)1x Resistor 1.0K ohm (1/4w)1x Resistor 1.5K ohm (1/4w)1x Resistor 4.7K ohm (1/4w)1x Resistor 470 ohm (1/4w)1x Resistor 1.1K ohm (1/4w)1x Resistor 3.0K ohm (1/4w)1x IC MOC30631x 3-Position Terminal Block (5.08mm)2x Rubber GrommetsFeatures:Customizable control signal voltage3VDC to 26VDC control signal rangeDrive directly from microcontroller pin with as little as 3VDC @ 3mAConnects directly to Arduino, Raspberry Pi, Beaglebone or other 3.3V or 5V MCU20A switching capacity; 5300vrms isolationTwo wire control signal; no separate DC power source requiredNo exposed ac wiringLED status indicatorDocuments:Instruction SheetDatasheets:MOC3063AZ21501 RelayProduct Video

Description

Want to control a standard wall outlet device with your micro controller, but don’t want to mess with the high voltage wiring? This might just be the right device for you! The PowerSwitch Tail Kit is designed to allow you to safely control an outlet device without exposing any 120VAC voltages while being able to “customize” it to meet your applications needs. You can optimize the voltage required for the control signal by selecting and installing different resistor values for R1/R2 slots on the kit PCB. With this ability to choose the control signal voltage the PowerSwitch Tail Kit is given the ability to provide an input voltage from 3VDC all the way to 26VDC. Additionally, power cables are sold separately to give you the choice of cable you wish to use with this kit.This variation of the PowerSwitch Tail is sold as an easy-to-assemble kit and includes everything listed below with clear assembly instructions listed in the documents section.Includes:1x PowerSwitch Tail PCB1x PowerSwitch Tail Enclosure (w/ Case and PCB Screws)1x Relay (120VAC, 40A)1x Red LED (3mm)1x Metal Oxide Varistor 14mm (130V)1x Metal Oxide Varistor 7mm (130V)1x Resistor 1.0K ohm (1/4w)1x Resistor 1.5K ohm (1/4w)1x Resistor 4.7K ohm (1/4w)1x Resistor 470 ohm (1/4w)1x Resistor 1.1K ohm (1/4w)1x Resistor 3.0K ohm (1/4w)1x IC MOC30631x 3-Position Terminal Block (5.08mm)2x Rubber GrommetsFeatures:Customizable control signal voltage3VDC to 26VDC control signal rangeDrive directly from microcontroller pin with as little as 3VDC @ 3mAConnects directly to Arduino, Raspberry Pi, Beaglebone or other 3.3V or 5V MCU20A switching capacity; 5300vrms isolationTwo wire control signal; no separate DC power source requiredNo exposed ac wiringLED status indicatorDocuments:Instruction SheetDatasheets:MOC3063AZ21501 RelayProduct Video

If you are interested in Internet of Things (IoT) or M2M projects check our open source sensor platform Waspmote which counts with more than 100 sensors available to use 'off the shelf', a complete API with hundreds of ready to use codes and a low consumption mode of just 0.7µA to ensure years of battery life.

Know more at:

Get the Starter Kits at: