Cooking Hacks Forum
https://www.cooking-hacks.com/forum/

Z-axis motors problem.
https://www.cooking-hacks.com/forum/viewtopic.php?f=40&t=3922
Page 2 of 2

Author:  libelium-dev [ Thu Aug 01, 2013 11:37 am ]
Post subject:  Re: Z-axis motors problem.

Hi winitalia,

please try with this Marlin, I think that the first time you had the new version and we haven't tested it with our configuration.

https://www.dropbox.com/s/7zp9i6aw8jich ... lin_v1.rar

Thanks.

Regards.

Author:  winitalia [ Thu Aug 01, 2013 1:23 pm ]
Post subject:  Re: Z-axis motors problem.

Done.
Now's compiling correctly, but no motor seems to work. Neither x, nor y, nor z.

Author:  libelium-dev [ Fri Aug 02, 2013 8:06 am ]
Post subject:  Re: Z-axis motors problem.

Hi winitalia,

before moving the motors, do you press the home button? If you press it, please send us a photo of your board and your end stops. We want to know how you have wired the printer.

Regards.

Author:  winitalia [ Fri Oct 04, 2013 10:42 am ]
Post subject:  Re: Z-axis motors problem.

Ok.
We managed to solve the motor problems.
Now everything seems to work fine.
But...
...when we try to print something the filament does not want to stick to the bed while continuously moving the object.
:?
A video can say more then thousand words.

Printer Problem Video

We set the values on Cura exactly like the screenshots on your step-by-step guide.

Can you help us?

Author:  libelium-dev [ Sun Oct 06, 2013 10:57 pm ]
Post subject:  Re: Z-axis motors problem.

Hi winitalia,

to avois this, you have several options:

- Clean the bed really well with industrial acetone.

- Use hairspray to increase the adhesion of the plastic.

- Use kapton tape to transfer better the heat of the bed, you have to clean it very well with acetone.

Regards.

Author:  Ozista [ Sat Nov 30, 2013 2:34 pm ]
Post subject:  Re: Z-axis motors problem.

Hi All,

I have the same problem with my X axis and I guess it is the voltage to these *2 motors should be higher?!

Just came across how to measure the voltage on the driver: http://reprap.org/mediawiki/images/0/02 ... ecking.jpg

Hoping for a solution

Ozista

Author:  libelium-dev [ Mon Dec 02, 2013 8:42 am ]
Post subject:  Re: Z-axis motors problem.

Hi Ozista,

with which motors have you problems?

Normally, you have to measure in your drivers 0.4V, have you measure them?

Once you measure it, normally, in the Z-Axis (it has two motors) you have to give it more power with the potentiometer.


Thanks.

Regards

Author:  Ozista [ Tue Jan 14, 2014 1:57 am ]
Post subject:  Re: Z-axis motors problem.

Raul wrote:
Have you try with the DEFAULT_MAX_FEEDRATE ? my stepper motor start making noise but not move and i change to {5, 2, 2, 10} and goes fine. I don't have a cooking hacks machine, but i have ramps.


Thank you Raul, I have tried your IDEA and it works for me now FINALLY!!

Cheers Ozista

Author:  libelium-dev [ Tue Jan 14, 2014 8:10 am ]
Post subject:  Re: Z-axis motors problem.

Hi Ozista,

Thanks for your contribution to the Cooking Hacks community!

Regards.

Page 2 of 2 All times are UTC + 1 hour
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/