My Cart

315Mhz remote relay switch kits - 2 channels

19.5 €19.50

Availability: Retired

This remote switch allows you to remotely control any 12 Volt DC device. Perfect for controlling any 12V devices such as Lights , Fans, Landscaping Lighting and more. For PC Modders, the end of result of the Remote Control 12VDC kit are truly impressive and are sure to ooh and ah the crowds.

  • Frequency: 315Mhz.
  • Working voltage: 12VDC
  • Receiver sensibility: -105dbm
  • Emission distance: 100m in open ground
  • Size: 68mm*47mm*12mm

Each Relay owns one group of 3 pins:

And setup the corresponding pins on PT2272:

Relay Operation Modes:

The receiver has three modes that control how the relay outputs function.Momentary:

Move the switch position to set the selected relay(s) in momentary mode. Flip-Flop:

Remove the shunt to set the selected relay(s) in Flip-Flop mode. Latching:

Move the switch position to set the selected relay(s) in Latching mode. In latching mode, when the selected relay is activated by the transmitter, that relay will change its state and maintain it until power to the receiver is removed or interrupted.
Please refer to the simple drawing for the 315Mhz RF link. On the transimitter side, You would need to supply 3-5VDC to the "+12V" pin,(Caution: the 12v is an error silk screen on PCB, never give it more than 5V, and set "TE" high(5V) to enable transmission. On the receiver side, you may use +5VDC(aka VCC) for power and read the output from D0~D3. "TV" will indicate thenever there is changed data incoming.
Datasheetfor PT2272 and PT2262

Description

This remote switch allows you to remotely control any 12 Volt DC device. Perfect for controlling any 12V devices such as Lights , Fans, Landscaping Lighting and more. For PC Modders, the end of result of the Remote Control 12VDC kit are truly impressive and are sure to ooh and ah the crowds.

  • Frequency: 315Mhz.
  • Working voltage: 12VDC
  • Receiver sensibility: -105dbm
  • Emission distance: 100m in open ground
  • Size: 68mm*47mm*12mm

Each Relay owns one group of 3 pins:

And setup the corresponding pins on PT2272:

Relay Operation Modes:

The receiver has three modes that control how the relay outputs function.Momentary:

Move the switch position to set the selected relay(s) in momentary mode. Flip-Flop:

Remove the shunt to set the selected relay(s) in Flip-Flop mode. Latching:

Move the switch position to set the selected relay(s) in Latching mode. In latching mode, when the selected relay is activated by the transmitter, that relay will change its state and maintain it until power to the receiver is removed or interrupted.
Please refer to the simple drawing for the 315Mhz RF link. On the transimitter side, You would need to supply 3-5VDC to the "+12V" pin,(Caution: the 12v is an error silk screen on PCB, never give it more than 5V, and set "TE" high(5V) to enable transmission. On the receiver side, you may use +5VDC(aka VCC) for power and read the output from D0~D3. "TV" will indicate thenever there is changed data incoming.
Datasheetfor PT2272 and PT2262

If you are interested in Internet of Things (IoT) or M2M projects check our open source sensor platform Waspmote which counts with more than 100 sensors available to use 'off the shelf', a complete API with hundreds of ready to use codes and a low consumption mode of just 0.7µA to ensure years of battery life.

Know more at:

Get the Starter Kits at: