Wireless

4,5 dBi 868-900 SMAM-RP Antenna

Dimension: 21 cm.

Learn More

This is a simple to use, RS232 to serial base unit for the XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a RS232 cable, and you will have direct access to the serial and programming pins on the XBee unit. The board also supports DTR communication so you can reprogram and configure the XBee unit.

XBee modules, RS232 cable, and power supplies sold below.

Documents:

• Schematic
  
• X-CTU Software
• XBee Introduction and Buying Guide

Learn More

This is a simple to use, USB to serial base unit for the XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programming pins on the XBee unit.

You get the red board only. XBee modules and USB cable sold below.

Note: As of August 2010, all new boards now include a MIC5219 voltage regulator which is good for 500mA.

Documents:

• Schematic
  
• Eagle Files
• X-CTU Software
• XBee Introduction and Buying Guide
• Configuring XBees Tutorial
• USB FTDI Drivers for Windows, Linux, Mac

Learn More

This is a super long range 433mhz RF link kit Comes with VCO , PLL technology, steady Frequency and super anti-jamming ability. You can directly use it with your project like wireless data transport and remote control etc…
Spec:

    * Working volt : 5V
    * Working current: ≤2.5mA(5.0VDC)
    * principle of work:  Superhet（VCO, PLL）
    * Modulation：OOK/ASK
    * Working band:  433.92MHz  (customize service available)
    * Bandwidth:  1.5MHz
    * Sensitivity:  -105dBm (50Ω)
    * Rate: ＜5Kbps
    * Decoding form：PT2272
    * Antenna length:  18cm
    * Emission Distance: 2 KM

Datasheet for PT2272 and PT2262: http://www.datasheetcatalog.org/datasheet/PrincetonTechnologyCorporation/mXusxsq.pdf

Learn More

The kit is consisted of transmitter and receiver, popular used for remote control.

Basic spec:
Frequency: 315Mhz.
Modulation: ASK
Receiver Data Output: High - 1/2 Vcc, Low - 0.7v
Transmitter Input Voltage: 3-12V (high voltage = more transmitting power) 

Usage:
The popular link is like this: MCU -> Encoder -> Transmitter ------ Receiver -> Decoder -> MCU,

PT2262(Encoder) and PT2272(Decoder) are optional, their existence is to 1)avoid confusing when multiple RF links in range 2) isolate disturbance. You can integrate the encoding and decoding work to the MCUs on both side. Whenever there is no 315Mhz devices around, you may use it as direct cable connection.

Excuse for the documentation, we will work on them. Before that, please consult us for any details, we are happy to find the answer for you ^^ We tried them using the guide from Sparkfun, it's compatible. The only difference is in package, of some excess GND pins.

Learn More

Basic spec:
Frequency: 315Mhz.
Modulation: ASK
Working Voltage: 3-12VDC（Transmitter), 5VDC(Receiver)
Receiver Sensibility: -105dbm
Emission Distance: 100m in open ground
Warning: this kit is not suitable for data transfer but remote control. Safe for 2 commands/second.

Encoding and Decoding
The popular link is like this: MCU -> Encoder -> Transmitter ------ Receiver -> Decoder -> MCU,

PT2262(Encoder) and PT2272(Decoder) are optional, their existence is to 1)avoid confusing when multiple RF links in range 2) isolate disturbance. You can integrate the encoding and decoding work to the MCUs on both side. Whenever there is no 315Mhz devices around, you may use it as direct cable connection.

Please refer to the simple drawing for the 315Mhz RF link. On the transimitter side, You would need to supply 3-5VDC to the "+12V" pin, (Caution: the 12v is an error silk screen on PCB, never give it more than 5V）, and set "TE" high(5V) to enable transmission. On the receiver side, you may use +5VDC(aka VCC) for power and read the output from D0~D3. "TV" will indicate thenever there is changed data incoming.

Learn More

A wireless relay is a codec-adaptive RF receiver with single channel relay. It helps easily deployment of wireless AC control for electrical appliances.

• Max 30 difference codec, unlimited controller or transmitter of each codec  
• Adaption of most popular RF remote controller, except rolling code

• Lighting 
• Electrical door, window 
• Security  
• Industrial control  
• Home automation

Learn More

The RFBee is a RF module providing easy and flexible wireless data transmission between devices. It is based on a AVR Atmega168 working as a fully functional Arduino connected via SPI to a TI CC1101 RF transceiver.

Learn More

This is a Wireless car key FOB with 4 buttons: Lock,unlock,mute and alarm on.  A blue led will light on when any button were pressed. Use this FOB to communicate with Codec-Adaptive Wireless Relay for your remote control project.

Learn More

These wireless transmitters work with our 434MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair.

Note: These modules are indiscriminate and will receive a fair amount of noise.  Both the transmitter and receiver work at common frequencies and don't have IDs. Therefore, a method of filtering this noise and pairing transmitter and receiver will be necessary. The example code below shows such an example for basic operation. Please refer to the example code and links below for ways to accomplish a robust wireless data link.

Features:

• 434 MHz
• 500ft range (given perfect conditions)
• 4800bps data rate
• 5V supply voltage

Documents:

• Arduino Library
• Example Code
• Datasheet
• KLP Walkthrough Tutorial
• Good AVR Tutorial

Learn More

The RFM22B is a low-cost ISM FSK transceiver module which offers communication at 433MHz ISM and adjustable output power of up to +20 dBm. The wide operating voltage range of 1.8–3.6 V and low current consumption makes the RFM22B an ideal solution for battery powered applications.

Communication with the RFM22B is achieved via a standard 4-wire SPI interface. Three configurable general purpose I/Os are also available, the use of which can be tailored towards the needs of your project. A host of other features are also available including an 8-bit ADC, temperature sensor, RX and TX FIFOs, and low-battery detection. See the datasheet below for a complete description of every register and command.

The module comes in a 16-pin, 16 x 16mm, SMD package, with pins spaced by 2mm. Look for a breakout board coming soon!

Note: These modules are 433MHz and Rev3.0.

Features:

• Frequency Range: 433MHz ISM
• Sensitivity = -121 dBm
• Output power range: +20 dBm Max
• Data Rate = 0.123 to 256 kbps
• FSK, GFSK, and OOK modulation
• Power Supply = 1.8 to 3.6 V
• Ultra low power shutdown mode
• Digital RSSI
• Wake-up timer
• Auto-frequency calibration (AFC)
• Power-on-reset (POR)
• Antenna diversity and TR switch control
• Configurable packet handler
• Preamble detector
• TX and RX 64 byte FIFOs
• Low battery detector
• Temperature sensor and 8-bit ADC
• –40 to +85 °C temperature range
• Integrated voltage regulators
• Frequency hopping capability
• On-chip crystal tuning

Dimensions: 16 x 16mm (0.63 x 0.63 in)

Documents:

• Datasheet
• Product Page
• Example Code (ATmega328)
• SFE Eagle Library has this part!

Learn More

The RFM12B is a great inexpensive option for wireless communication; it's an ISM band FSK transceiver module implemented with a unique PLL. These modules operate in the 434MHZ band and fully comply with FCC and ETSI regulations.

This module has a wide voltage supply range of 2.2-3.8VDC. An SPI interface is used to send data and configure the RFM12 module. The configuration commands, described in the RF12 IC Datasheet linked below, can be used to set the data rate, frequency band, wake-up timer, transfer data, receive data from the 16-bit FIFO, and much more.

The module comes in a 14-pin SMD package, with pins spaced by 2mm. Check below for a breakout board.

Features:

• Low-cost, high-performance
• SPI compatible interface
• High data rate (up to 115.2 kbps in digital mode)
• Wakeup timer
• 2.2V-3.8V power supply
• Analog and digital RSSI outputs
• Differential antenna input
• Automatic antenna tuning
• 16-bit RX data FIFO
• PLL and zero IF technology
• Fast PLL lock time
• High resolution PLL with 2.5KHz step
• Programmable TX frequency deviation (from 15 to 240 kHz)
• Programmable receiver bandwidth (from 67 to 400 kHz)
• Analog and digital signal strength indicator
• Internal data filtering and clock recovery
• Clock and reset signal output for external MCU use
• 10MHz crystal for PLL timing

Dimensions: 15.9 x 16.1 mm (0.626 x 0.634 in)

Documents:

• Datasheet
• Programming Guide
• RF12B IC Datasheet
• Product Page
• RFM12 Library for Atmel AVR uC's

Learn More

The RN-XV module by Roving Networks is a certified Wi-Fi solution especially designed for customer who want to migrate their existing 802.15.4 architecture to a standard TCP/IP based platform without having to redesign their existing hardware.

The RN-XV module is based upon Roving Networks' robust RN-171 Wi-Fi module and incorporates 802.11 b/g radio, 32 bit processor, TCP/IP stack, real-time clock, crypto accelerator, power management unit and analog sensor interface.

Datasheet
User Manual
Tutorial

Learn More

Increase the effective range of your wireless devices with this 9 dBi 2,4 GHz SMAM-RP Antenna.

To install, just unscrew your current antenna, and attach the High Gain antenna in its place. There are no drivers to install, and no modifications to your setup are necessary.

Size: 39 cms.

Learn More

XBee Wi-Fi embedded RF modules provide simple serial to IEEE 802.11 connectivity. By bridging the low-power/low-cost requirements of wireless device networking with the proven infrastructure of 802.11, the XBee Wi-Fi creates new wireless opportunities for energy management, process and factory automation, wireless sensor networks, intelligent asset management and more. Focused on the rigorous requirements of these wireless device networks, the XBee Wi-Fi gives developers IP-to-the-device flexibility.

- Common XBee footprint allows OEMs to support a variety of wireless protocols with one footprint
- Flexible SPI and UART serial interfaces
- RPSMA, PCB, U.FL and wired whip antenna options
- Support for low power sleeping applications with < 2 μA power-down current
- 802.11n provides up to 65 Mbps data rate

Official Documentation from Digi Site
Manual
Datasheet
Getting Started Guide: XBee Wi-Fi Development Kit

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote.

Learn More

This is a breakout board for the Silicon Laboratories Si4703 FM tuner chip. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.

Using this board we are able to pick up multiple stations just as well as with a standard FM radio. The board breaks out all major pins and makes it easy to incorporate this great chip into your next radio project. Also, by plugging headphones into the 3.5mm audio jack, you effectively use the cable in your headphones as an antenna! Therefore, this board does not require an external antenna if using headphones or a 3.5mm audio cable longer than 3 feet.

Documents:

• Schematic
• Eagle Files
• Datasheet (Si4703)
• Datasheet (TPA6111A2)
• Arduino Example Code
• Arduino Library
• Programming Guide



Learn More

This nRF2401A module has the same minimum interface of 7 pins (all in a .1" spaced connector) as the original nRF2401A module, but the size is reduce by over 60%!

These are the nRF2401A 2.4GHz transceiver modules with built in chip antenna designed around the Nordic Semiconductor nRF2401A with high sensitivity and range. Units come with an empty 0.1" spaced footprint ready for a straight header, right angle header (recommended), or your own wires/umbilical cable.

The following pins are broken out:

• 3.3V VCC / GND
• CE : Chip Enable
• CS : Chip Select
• Channel 1 Interface (Data, CLK1, DR1)

NEW! Check out our comparative range test!

Specifications:

• Frequency: 2.4~2.524 GHz
• Modulation type: GFSK
• Operating Voltage: 3V
• Output Power: +0dBm
• Data Rate: 1Mbps and 250Kbps
• Miniscule footprint size: 0.5x0.675" (13x17mm)
• Operating Temperature: -40 ~ +85 C
• Long range:
  • 50ft. indoors
  • 125ft. line of sight
• Built-in 2.45GHz ceramic antenna
• Very low cost

Documents:

• Nordic nRF2401A Datasheet

Software: Example PIC Code for 4-byte payload and 29-byte payload
Supported Antennae: Hah! It's built in!

Check out these handy calculators that help with antenna design.

Sold by single units. We recommend ordering two for a complete link.

Learn More

These are the 1.25mm pitch, 10-pin SMD connectors that mate directly with the RF-24G module.

Documents: RF-24G Connector

Learn More

This is a nicely packaged key FOB that contains a Nordic nRF24L01+ radio and a ATtiny24 for control. Press any one of 5 buttons and the ATtiny24 will wake up, transmit the buttons being pressed, a 16-bit integer value of the total button presses since last battery replacement, and then return to low-power sleep. The simple to replace 20mm coin cell will last for over 3 years. This unit comes fully assembled with battery and enclosure. FOB transmission range is quite nice at over 100ft. Use this FOB to communicate with any nRF24L01+ radio module for your next remote control project.

Features:

• Small size
• 100ft range
• Pre-programmed
• 4uA average current

Documents:

• Schematic
• Eagle Files
• FOB firmware
• Example receiver firmware
• Great Nordic tutorials

Check out these handy calculators that help with antenna design.

Learn More

This is only the 315MHz transmitter. This will work with the RF Links at 315MHz at either baud rate. Only one 315MHz transmitter will work within the same location.

This wireless data is the easiest to use, lowest cost RF link we have ever seen! Use these components to transmit position data, temperature data, even current program register values wirelessly to the receiver. These modules have up to 500 ft range in open space. The transmitter operates from 2-12V. The higher the Voltage, the greater the range - see range test data in the documents section.

We have used these modules extensively and have been very impressed with their ease of use and direct interface to an MCU. The theory of operation is very simple. What the transmitter 'sees' on its data pin is what the receiver outputs on its data pin. If you can configure the UART module on a PIC, you have an instant wireless data connection. The typical range is 500ft for open area.
This is an ASK transmitter module with an output of up to 8mW depending on power supply voltage. The transmitter is based on SAW resonator and accepts digital inputs, can operate from 2 to 12 Volts-DC, and makes building RF enabled products very easy.

Features:

• 315  MHz Transmitter Operation
• 500 Ft. Range - Dependent on Transmitter Power Supply
• 2400 or 4800bps transfer rate
• Low cost
• Extremely small and light weight

Documents:

• KLP Walkthrough Tutorial
• Good AVR Tutorial
• Transmitter Datasheet

Supported Antennae: 30-35cm of wire

Learn More

Bees shield will make interfacing multiple Bee-style (XBee, GPS Bee, Bluetooth Bee and etc) easier than ever before. Aside from dual Bee style 20p 2.0 pitch socket, it also has large proto area, customizable software serial port for easier prototyping.

Features

• Dual Bee type socket
• 3 indicator LED(ON/Sleep, RSSI, ASSOC)for each Xbee
• Full size with free drills
• Reset button for each Xbee
• Reset button for base board
• Provide maximal 500mA under 3.3V
• Full break out for each Bee
• Switchable of communication with FTDI-USB /Base board

Learn More

The DFRobot Xbee USB adapter is used for the XBee module configuration parameters to facilitate or to use as a wireless data transmission. It can be easily connected to a PC via mini USB cable. Further, it has XBee-setting support software X-CTU. It can also be used as a USB-TTL adapter.

Features

•  Used for the XBee module configuration parameters
•  Easily connected to a PC via mini USB cable
•  XBee-setting support software X-CTU
•  Also used as a USB-TTL adapter
•  Voltage: +5V(USB Power)

Learn More

Arduino shield with a socket for wireless modules like Digi Xbee, Bluetooth, RFID or Wifi Modules. Built in 3.3V voltage regulator, active voltage translators and prototyping area

Learn More

GPRS/GSM Quadband Module for Arduino (SIM900) offers GPRS connection to your Arduino board.
It includes the SIM900 communication module from SIMCom. It is necessary an antenna in order to establish a communication.
You can send SMS, make calls or create TCP and UDP sockets in order to send the information to the Internet. HTTP and FTP protocols are also available in order to send the information to the cloud directly from your Arduino.

Documentation:
- Tutorial
- Schematic
- AT Commands
- SIM900 Module Info

NOTE: The Arduino/Raspberry Pi jumper MUST be in Arduino position. The Raspberry Pi position should be used only if the shield is connected to a Raspberry Pi. A wrong position of this jumper can damage the GPRS shield.

Differences between SIM900 and HiLo Modules
- GPRS_Pro performs the same actions that GPRS module (some functions had been enhanced) and new functions has been added such as multiconnection for TCP/IP and UDP/IP clients, audio control or operator selection.
- Regarding power consumption it has been reduced from 56µA to 30µA in power down mode (GPRS_OFF power mode).
- The SIM900 module improves TCP/IP and UDP/IP connections adding new features such as TCP/IP server and multiconnection mode that allows up to 8 TCP/UDP clients or up to 7 TCP/UDP clients and 1 TCP/IP server. Extra functions such as autosending timer, add IP headers, setting DNS servers,... have been added.
- Also uploading and downloading functions have been upgraded to allow to select the origin and destiny folder into the SD card and FTP server.
- New functions allow to manage speaker level, Calling Line Identification (CLI) , mute, call alert. Also GSM/GPRS operator connection can be managed with functions such as get current operator, set preferred operator list, get cell information.

Important! Powering the board. You need an External Power Supply.

If you need information of our old HiLo GPRS Quadband Module, you can check it here. Note than both are using the same breakout board so we have had to modify it to be compatible with the new SIM900 module, adding a diode in the voltage regulator.

NOTE: If you are looking for a complete solution to use 3G, GPRS and A-GPS, you can use our 3G/GPRS shield for Arduino (3G + GPS) or our Kit with Audio/Video

NOTE: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote which counts with more than 50 sensors available to use.

Learn More

The XtremeRange2 represents the first true carrier class 802.11b/g-based 2.4GHz radio module specifically designed for mesh, bridging, and infrastructure applications requiring the highest levels of performance and reliability without compromise. Features 600mW Avg. TX Power and Integrated EMP/ESD Protection Circuitry.

- Processor Specs: Atheros, 6th Generation, AR5414
- Radio Operation: IEEE 802.11b/g, 2.4GHz
- Interface: 32-bit mini-PCI Type IIIA
- Operation Voltage: 3.3VDC
- Antenna Ports: Single MMCX
- Temperature Range: -45 to +90C (extended temp version up to +95C)
- Security: WPA, WPA2, AES-CCM & TKIP Encryption, 802.1x,64/128/152bit WEP
- Data Rates: 6Mbps, 9Mbps, 12Mbps, 24Mbps, 36Mbps, 48Mbps. 54Mbps
- TX Channel Width Support: 5MHz / 10MHz / 20MHz / 40MHz
- RoHS Compliance: YES
- Avg. TX Power: 28dBm, +/-1dB
- Max Current Consumption: 1.30A, +/-100mA
- Indoor Range (Antenna Dependent): up to 200meters
- Outdoor Range (Antenna Dependent): over 50km
- Operating System Support: Linux MADWIFI, WindowsXP, Windows2000

Learn More

Features:

- Atheros XSPAN family chipset
- 2.4/5GHz IEEE 802.11n draft compliant and backward compatible with 802.11
- 2.4/5GHz Dual-band 2x2 MIMO spatial multiplexing technique
- Maximum 20dBm output (per antenna port) - 23dBm aggregate
- Supports up to 300Mbps physical data rates
- Delivers 10 times the throughput and nearly twice the range of legacy 802.11 and 802.11b/g networks
- Transmission Power Control (IEEE 802.11h TPC)
- Dynamic Frequency Selection (DFS)
- Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard)
- 2 x U.FL Antenna Connectors

Datasheet

Learn More

Senao / Engenius NMP-8602+ Having high output power is always a great bonus when designing your embedded application. Using the latest in technology expertise, Senao has fine tuned the NMP-8602+ mini-PCI to be the most powerful RF module in the market today. The slim form factor allows for small physical applications. Your all-in-one solution encompassing 802.11a, 802.11b, and 802.11g networking technology will be the last mini-PCI high powered solution you will ever need.

Part number: NMP-8602+, EMP-8602+

Up to 400mW transmission power for maximum range, throughput speeds, and signal strength

Complete IEEE 802.1x client support with EAP-TLS, EAPTTLS supplicants

802.11e standards supported for Wireless Multimedia Enhancements QoS

Atheros 6thG Mini-PCI Adapter

Datasheet

Learn More

The XtremeRange5 represents the first true carrier class 802.11a based 5GHz radio module specifically designed for mesh, bridging, and infrastructure applications requiring the highest levels of performance and reliability without compromise. Featuring Industry Leading 600mW Avg TX Power (1000mW Peak).

Processor Specs: Atheros, 6th Generation, AR5414 with SuperA/Turbo Support
Radio Operation: IEEE 802.11a, 5GHz
Interface: 32-bit mini-PCI Type IIIA
Operation Voltage: 3.3VDC
Antenna Ports: Single MMCX
Temperature Range: -45 to +85C (extended temp version up to +95C)
Security: 802.11i, AES-CCM & TKIP Encryption, 802.1x, 64/128/152bit WEP
Data Rates: 6Mbps, 9Mbps, 12Mbps, 24Mbps, 36Mbps, 48Mbps, 54Mbps
TX Channel Width Support: 5MHz / 10MHz / 20MHz / 40MHz
RoHS Compliance: YES
Avg. TX Power: 28dBm, +/-1.5dB
Max Current Consumption: 1.80A, +/-100mA
Indoor Range (Antenna Dependent): over 150m
Outdoor Range (Antenna Dependent): over 50km
Operating System Support: Linux MADWIFI, WindowsXP, Windows2000

Learn More

Features

Atheros XSPAN family chipset
2.4GHz IEEE 802.11n draft compliant and backward compatible with 802.11b/g
2.4GHz single-band 2x2 MIMO spatial multiplexing technique
Maximum 26dBm output (per antenna port) - 29dBm aggregate
Supports up to 300Mbps physical data rates
Delivers 10 times the throughput and nearly twice the range of legacy 802.11b/g network
Transmission Power Control (IEEE 802.11h TPC)
Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard)
2 x MMCX Antenna Connectors 

Learn More

Features
Atheros XSPAN family chipset
5GHz IEEE 802.11n compliant and backward compatible with 802.11a
5GHz Single-band MIMO 2x2 spatial multiplexing technique
Maximum 23dBm output (per chain)/26dBm aggregate
Built-in ESD Protection with ESD/EMP Immunity Threshold: 15KeV
4.9GHz support (Optional)
Enhanced noise immunity and sensitivity
Delivers 10 times the throughput and nearly twice the range of legacy 802.11a network
Transmission Power Control (IEEE 802.11h TPC)
Dynamic Frequency Selection (DFS)
Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard)
2 x MMCX or 2 x U.FL Antenna Connectors
Cost-effective and flexible for outdoor broadband wireless applications

Learn More

This Bluetooth Module PRO has been mainly designed to discover high amount of bluetooth devices in a variable area. It can be connected in a Xbee shield for Arduino to work.

Technical characteristics:
- Chip: Bluegiga WT12
- Bluetooth v2.1 + EDR. Class 2
- TX Power: 7 Power levels [-27dBm, +3dBm]
- RX sensitivity:  -90 dBm
- Antenna: 2dBi
- Range: from 10 to 50 meters depending tx power and environment conditions.
- Received Strength Signal Indicator (RSSI) for each scanned device
- Class of Device (CoD) for each scanned device

Special features:
- Bluetooth module integrates a firmware called Iwrap, developed by manufacturer which offers many possibilities.
- Moreover, Libelium has developed a specific API to allow using this module with Waspmote. There are many useful functions which can be used as a guideline for other designs. Refer to Libelium web site for more information.

Download the Fritzing library to include in your electronic designs here

Documentation:
- Tutorial
- Schematic
- Module Info

NOTE: If you don't need to use the full features of this module, maybe you are interested in our Bluetooth Module for Arduino.

NOTE: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote which counts with more than 50 sensors available to use.

Learn More

Quadband Mobile SIM900 - Arduino Pack contains:
- Arduino UNO
- GPRS Quadband SIM900 Module for Arduino

Important! Powering the board. You need an External Power Supply.

NOTE: If you are looking for a complete solution to use 3G, GPRS and A-GPS, you can use our 3G/GPRS shield for Arduino (3G + GPS) or our Kit with Audio/Video

NOTE: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote which counts with more than 50 sensors available to use.

Learn More

RP-SMA male to RP-SMA female adapter.
Lenght: 7cms Learn More

This kit is used for one way wireless communication at a frequency of 315MHz and includes a transmitter module and a receiver module. The twig configuration of this kit allows for around 40 meters of transmitting distance indoors, or around 100 meters outside.

Features
GROVE compatible interface.
Uses ASK (Amplitude Shift Keying) Modulation.
One way communication.
Application Ideas
Remote control
Remote automation
Alarm

Learn More

Arduino shield with a socket for wireless modules like Digi Xbee, Bluetooth, RFID or Wifi Modules. Built in 3.3V voltage regulator, active voltage translators and prototyping area

Learn More

The new 3G shield for Arduino enables the connectivity to high speed WCDMA and HSPA cellular networks in order to make possible the creation of the next level of worldwide interactivity projects inside the new "Internet of Things" era.

The module counts also with an internal GPS what enables the location of the device outdoors and indoors combining standard NMEA frames with mobile cell ID triangulation using both assisted-mobile (A-GPS) and mobile-based (S-GPS) modes.

You can also find our Audio/Video Kit to complete this 3G/GPRS Shield. Antennas not included.

You will need to update your firmware to play mp3. The update is available here. Uncompress and run it in a PC with Windows (emulated Windows not supported).

Features: - WCDMA and HSPA 3G networks compatibility
- Internal GPS for Assisted A-GPS and Supported S-GPS modes
- Video Camera (640x480) for video and photo recordings available
- Audio Kit including microphone, speaker, hands free and headphones available
- SD file system up to 32GB
- Works as a standard 3G modem in Linux/Windows/MacOS (~7.2Mbps download, ~5.5Mbps upload)
- Talk directly to web servers by HTTP/HTTPS (secure)
- Upload and download files directly by FTP/FTPS (secure)
- Send and receive mails by POP3/SMTP
- Play compressed audio files

Download the Fritzing library to include in your electronic designs here

Documentation:
- Tutorial + Complete Reference Guide
- Video-Tutorial
- SIM5218 AT command manual
- 3G shield schematic

NOTE: The Arduino/Raspberry Pi jumper MUST be in Arduino position. The Raspberry Pi position should be used only if the shield is connected to a Raspberry Pi. A wrong position of this jumper can damage the 3G shield.

NOTE: If you only need to send SMS or use a low bandwidth for data transfer you can use our cheaper GPRS/GSM Quadband SIM900 module for Arduino.

NOTE: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote which counts with more than 50 sensors available to use.

Learn More

The new 3G shield for Arduino enables the connectivity to high speed WCDMA and HSPA cellular networks in order to make possible the creation of the next level of worldwide interactivity projects inside the new "Internet of Things" era.

The module counts also with an internal GPS what enables the location of the device outdoors and indoors combining standard NMEA frames with mobile cell ID triangulation using both assisted-mobile (A-GPS) and mobile-based (S-GPS) modes. Antennas not included.

You will need to update your firmware to play mp3. The update is available here. Uncompress and run it in a PC with Windows (emulated Windows not supported).

This Kit includes:
- 3G/GPRS shield for Arduino (3G + GPS)
- 2Gb microSD card
- Electret Microphone
- VGA Sensor Camera
- Jumper Wires (F/M)
- Speaker 8 ohm 2W
- Handsfree headphones
- miniUSB Cable
- Internal Speaker

Features:
- WCDMA and HSPA 3G networks compatibility
- Internal GPS for Assisted A-GPS and Supported S-GPS modes
- Video Camera (640x480) for video and photo recordings available
- Audio Kit including microphone, speaker, hands free and headphones available
- SD file system up to 32GB
- Works as a standard 3G modem in Linux/Windows/MacOS (~7.2Mbps download, ~5.5Mbps upload)
- Talk directly to web servers by HTTP/HTTPS (secure)
- Upload and download files directly by FTP/FTPS (secure)
- Send and receive mails by POP3/SMTP
- Play compressed audio files

Download the Fritzing library to include in your electronic designs here

Documentation:
- Tutorial + Complete Reference Guide
- Video - Tutorial
- SIM5218 AT command manual
- 3G shield schematic

NOTE: The Arduino/Raspberry Pi jumper MUST be in Arduino position. The Raspberry Pi position should be used only if the shield is connected to a Raspberry Pi. A wrong position of this jumper can damage the 3G shield.

NOTE: If you only need to send SMS or use a low bandwidth for data transfer you can use our cheaper GPRS/GSM Quadband SIM900 module for Arduino.

NOTE: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote which counts with more than 50 sensors available to use.

Learn More

SPECIAL OFFER WHILE STOCKS LAST!!

A cable-less solution developed for controlling your Roomba. The RooTooth v2 communicates with any Bluetooth^® enabled device using the Serial Port Profile (SPP). You can now tell the Roomba when to wake up, when to clean, and when to shut off. You can even remotely drive your Roomba from your computer or from the WiTilt!

This product requires that the SCI (serial command interface) has been installed on your Roomba. SCI has been installed on all Roombas manufactured after October 24th, 2005. Please verify that your Roomba is compatible by checking here.

The new RooTooths are based on the Roving Network bluetooth module. The command set has changed from the original user guide written by Roomba Dev Tools. The new datasheet is below. The Rootooths are configured to 57600bps to work at the Roomba's default communication rate.

Documents:

• Schematic
• Eagle Files
• Roving Network Module Command Set
• Roomba Serial Command Interface

Learn More

RFID 13.56 MHz Module for Arduino can be connected to Arduino using a XBee shield and will communicate it using the Arduino serial port (UART).

Chip: PN532 by NXP.
Compatibility: Reader/Writer mode supporting ISO 14443A / MIFARE /
FeliCaTM / NFCIP-1
Distance: 5cm
Max capacity: 4KB
Tags: cards, keyrings, stickers

Applications: 
Located based services (LBS)
Logistics (assets tracking, supply chain)
Access management
Electronic prepaid metering (vending machines, public transport)

Smartphone interaction (NFCIP-1 protocol)

Tutorial

Datasheet

Schematic

User Manual

Download the Fritzing library to include in your electronic designs here

If you are looking for RFID 125 kHz solutions, you can take a look on our RFID Module for Arduino.

NOTE: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote which counts with more than 50 sensors available to use.

Learn More

RFID 13.56 MHz / NFC Card to use with our new RFID 13.56 MHz / NFC Module for Arduino

Learn More

RFID 13.56 MHz / NFC Keyring for using with our RFID 13.56 MHz / NFC Module for Arduino

Learn More

This kit is used for one way wireless communication at a frequency of 433MHz and includes a transmitter module and a receiver module. The twig configuration of this kit allows for around 40 meters of transmitting distance indoors, or around 100 meters outside.

Features
GROVE compatible interface.
Uses ASK (Amplitude Shift Keying) Modulation.
One way communication.
Application Ideas
Remote control
Remote automation
Alarm

Learn More

Bluetooth Extreme has been designed to make high performance and massive Bluetooth connections as it allows to discover up to 250 devices in a certain area, and to perform long range connections with them (up to 30 m with line of sight). It works in Linux, Windows and MacOS.

It comes with a 5dBi Antenna.

Technical characteristics:
Chip: Bluegiga WT12
Bluetooth v2.1 + EDR. Class 2
TX Power: 7 Power levels [-27dBm, +3dBm]
RX sensitivity: -90 dBm
Antenna: 5 dBi 2,4 GHz Antenna RPSMA
Range: depending of the antenna
Received Strength Signal Indicator (RSSI)
Class of Device (CoD) for each scanned device

Documentation:
Tutorial

Learn More

RFID Module for Arduino can be connected to Arduino using a XBee shield and will communicate it using the Arduino serial port (UART).

Features:
- RFID chip: SM125
- Frequency: 125KHz
- UART interface up to 115200 bps
- I2C interface up to 400 kHz
- TAGs: Atmel / Temic T55xx and EM4102(Unique)
- Antenna: 860 uH 10%, 40 x 15 mm
- Working distance: up to 10 cm (depending on the antenna size)
- Secure Transmissions: 4Byte password
- Sleep mode enabled (20uA)
- Modulation: supports Manchester RF/64, Manchester RF/32

Documentation:
Tutorial RFID module
Schematic of the board
RFID chip manual

Take a look on the Product Review by Arduteka & Cooking Hacks.

Check also the RFID Tutorial of our friend Jeremy Blum.

Download the Fritzing library to include in your electronic designs here

If you are looking for RFID 13.56 MHz solutions, you can take a look on our new RFID 13.56 MHz/NFC Module for Arduino.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

GPS tiny pen is a small device that you can connect to a computer to get position and altitude, as well as speed, date and time on UTC (Universal Time Coordinated).

It uses the standard NMEA protocol (www.nmea.org) to transmit the position data via serial port.

It includes miniUSB wire and can be used with many navigation NMEA compatible software

Size: 3.5x6x2 cms.

Tutorial
Videotutorial
Firmware GPS

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

[X-TICK] - XBee Programmable USB Stick is a small device battery powered totally programmable. It has 4 position joystick and 2 leds you can program as you want. Just plug it into your computer and you'll charge its lithium battery (380 mAh), program it as you want and you can integrate it into your ZigBee sensor network, you can controll events, check if the pen is inside a building, open /close doors / windows ...
Connected to the computer it also can be used as a gateway to collect data from the ZigBee sensor network.

It includes miniUSB wire.

Size: 3.5x6x2 cms.

Documentation:
Tutorial
Manual
Indoor location using 802.15.4 ZigBee
Enabling ZigBee and 802.15.4 in PDA and mobile phones

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

Get Bluetooth connection on your computer with this device. You can use it to link your computer with our Bluetooth module

• Bluetooth V2.0 Class 1 (class 1 is manufacturer rated)
• Maximum wireless distance: 100 meters (as per Bluetooth class 1 standard)
• Supports native Windows bluetooth stack (Windows XP and Vista)

Learn More

125Khz, EM4100 standard.

Combo includes:
Different color key tag * 3
Blank card with Serial Number * 2

Compatible with Arduino RFID module.

Learn More

Bluetooth Module for Arduino is able to be plugged into the XBee Shield and get a serial communication between the computer and an Arduino board through Bluetooth protocol.

Documentation:
Bluetooth Tutorial
Bluetooth Videotutorial

Special Options:
- Minimum and Maximum RSSI thresholds control
- Adaptive Frequency Hopping
- Security: Authentication, Pairing and Encryption
- Store 5 different trusted devices in its internal memory
- Master or Slave operation supported

Download the Fritzing library to include in your electronic designs here

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

Bluetooth - Arduino Pack contains an Arduino UNO and the new Bluetooth Module for Arduino.

Documentation:
Bluetooth Tutorial
Bluetooth Videotutorial

Bluetooth Chip: eUnistone 31308/2
Version: Bluetooth 2.0 + EDR (Configurable BT 1.2)
TX Power: 2.5dBm
RX Sensitivity: -86dBm
Antenna: 2dBi
Outdoor Range: 60 m LOS (Line of sight)
Indoor Range: 40 m NLOS (Non line of sight)
(Range measured between the Bluetooth module for Arduino and the BT Linksys dongle)
Special Options:
- Minimum and Maximum RSSI thresholds control
- Adaptive Frequency Hopping
- Security: Authentication, Pairing and Encryption
- Store 5 different trusted devices in its internal memory
- Master or Slave operation supported

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

This product has been replaced by a new version. See the new Quadband Mobile SIM900 - Arduino Pack.

Quadband Mobile - Arduino Pack contains:
- Arduino UNO
- GPRS Quadband Module for Arduino

IMPORTANT: Powering the board

Tutorial
Video-Tutorial

NOTE: If you are looking for a complete solution to use 3G, GPRS and A-GPS, you can use our 3G/GPRS shield for Arduino (3G + GPS) or our Kit with Audio/Video

NOTE: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote which counts with more than 50 sensors available to use.

Learn More

Kit composed of Arduino UNO and the new GPS module for Arduino. Internal GPS antenna is sold separately.

Tutorial
Video-Tutorial

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

Internal GPS Antenna to use with our GPS module.

• Frequency: GPS 1575.42 MHz
• Impedance: 50 Ohms
• Polarization: RHCP
• Gain: 24-26dBi
• Supply Voltage: 3V to 5V
• Connector: UFL
• Housing size: 14mm x14mm x 8,1mm
• Operating temperature: -40°C to +85°C

Download the Fritzing library to include in your electronic designs here

Learn More

External GPS Antenna for using with our GPS module. It includes a SMA-Female to UFL pigtail.

• Frecuency: GPS 1575.42 MHz
• Impedance: 50 Ohms
• Polarization: RHCP
• Gain: 26dB at 3V, 28dB at 5V
• VSWR: <1.2:1
• Supply Voltage     2.7V - 5.5V
• Current: 15mA - 25mA
• Power (max.): 125mW
• Connector: SMA Male
• Size: 41mm x 34mm x 13.7mm
• Operating temperature     -40°Cto +85°C

Learn More

GPS Module for Arduino is a small electronic circuit that allows to connect to your Arduino board to get position and altitude, as well as speed, date and time on UTC (Universal Time Coordinated). Internal GPS antenna is not included. It is sold as an optional and it is required to use the module.

The assembled module is Vincotech A1080-B that uses the standard NMEA and SIRF III protocols (www.nmea.org) to transmit the position data via serial port.

GPS module for Arduino is a perfect complement for developing geolocalization applications.

It can be used with many navigation NMEA compatible software

IMPORTANT! Handle with care the internal antenna. It's fragile. To get a correct fixation with the satellites, please cover the module with a plastic box

Tutorial GPS module
Video-Tutorial

Firmware GPS

 

Download the Fritzing library to include in your electronic designs here

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

Read Only Cards to use with our Arduino RFID Module. EM4100 compatible

Download the Fritzing library to include in your electronic designs here

Learn More

Read-Write Cards to use with our new Arduino RFID Module. T55XX Compatible

Download the Fritzing library to include in your electronic designs here

Learn More

802.15.4 Shield for the Arduino Board. It includes Digi XBee™ 802.15.4 OEM RF Module, up to 100m distance transmission. With this module it can be built low-power wireless communication applications, suchs as sensor networks. Board comes fully assembled and tested (without Arduino board).

Documentation:
Arduino XBee Tutorial
Video Tutorial
XBee Module Datasheet

Disclaimer: XBee 802.15.4 and ZB modules are NOT compatibles

Download the Fritzing library to include in your electronic designs here

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

802.15.4 Shield for the Arduino Board. It includes Maxstream XBee™ 802.15.4 OEM RF Module, up to 100m distance transmission. With this module it can be built low-power wireless communication applications, suchs as sensor networks. Board comes fully assembled and tested (without Arduino board) and includes 2dBi Antennas+Pigtail (UFL-SMA).

Documentation:
Arduino XBee Tutorial
XBee Module Datasheet

Disclaimer: XBee 802.15.4 and ZB modules are NOT compatibles

Download the Fritzing library to include in your electronic designs here

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

ZigBee Shield for the Arduino Board.

The Zigbee module is the Maxstream XBee™ ZB Module with on board chip antenna, up to 100m distance transmission. With this module it can be built low-power wireless communication applications, suchs as sensor networks.

Board comes fully assembled and tested (without Arduino board).

Documentation:

Arduino XBee Tutorial

XBee Module Manual

Disclaimer: XBee 802.15.4 and ZB modules are NOT compatibles

Download the Fritzing library to include in your electronic designs here

Download the Fritzing library to include in your electronic designs here

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

ZigBee Shield for the Arduino Board with UFL antenna 2.4GHz 2dB.

The Zigbee module is the Maxstream XBee™ ZB Module with UFL antenna, up to 100m distance transmission. With this module it can be built low-power wireless communication applications, suchs as sensor networks.

Board comes fully assembled and tested (without Arduino board).

Documentation:

Arduino XBee Tutorial

XBee Module Manual

Disclaimer: XBee 802.15.4 and ZB modules are NOT compatibles

Download the Fritzing library to include in your electronic designs here

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

External GPRS-GSM-UMTS Antenna to use with our Arduino GPRS Module. It includes a SMA-Female to UFL pigtail.

• Frequency: 850 MHz-900 MHz-2.1 GHz-1800 MHz-1900 MHz
• Impedance: 50 Ohms
• Mounting: on glass
• Polarization: horizontal
• Gain: 2.14dBi
• VSWR: <2:1
• Power handling: 25W
• Cable length: 2.5m
• Connector: SMA Male
• Size: 117mm x12,5mm x 4mm
• Operating temperature: -40°Cto +85°C

Learn More

Internal GPRS-GSM Antenna to use with our Arduino GPRS Module.

• Frequency: 900 MHz-2.1 GHz-1800 MHz
• Impedance: 50 Ohms
• Polarization: vertical
• Gain: 0 dBi
• VSWR: <2:1
• Power handling: 25W
• Connector: UFL
• Housing size: 35mm x 6mm
• Operating temperature: -40°C to +85°C

Download the Fritzing library to include in your electronic designs here

Learn More

RFID 125 kHz - Arduino Pack contains an Arduino UNO and the new RFID 125 kHz Module for Arduino.

Available the 5 pcs-set of Read Only and Read-Write Cards.

Documentation:
Tutorial RFID 125 kHz module for Arduino

Check also the RFID Tutorial of our friend Jeremy Blum.

Specifications:

• RFID chip: Sonmicro SM125
• UART interface up to 115200 bps
• I2C interface up to 400 kHz
• Supports Atmel / Temic T55xx and EM4102(Unique) tags
• Supports Manchester RF/64, Manchester RF/32 modulation
  
  

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

The New Bluetooth Tracking - Arduino Pack contains an Arduino UNO, a GPS module for Arduino and the new Bluetooth Module for Arduino (RFID/BT/XBee Shield included).

Documentation:
Bluetooth Tutorial
Bluetooth Videotutorial

Bluetooth Chip: eUnistone 31308/2
Version: Bluetooth 2.0 + EDR (Configurable BT 1.2)
TX Power: 2.5dBm
RX Sensitivity: -86dBm
Antenna: 2dBi
Outdoor Range: 60 m LOS (Line of sight)
Indoor Range: 40 m NLOS (Non line of sight)
(Range measured between the Bluetooth module for Arduino and the BT Linksys dongle)
Special Options:
- Minimum and Maximum RSSI thresholds control
- Adaptive Frequency Hopping
- Security: Authentication, Pairing and Encryption
- Store 5 different trusted devices in its internal memory
- Master or Slave operation supported

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

This product has been replaced by a new version. See the new GPRS/GSM Quadband Module SIM900 for Arduino.

GPRS Quadband Module for Arduino offers GPRS connection to your Arduino board. It includes the HiLo SAGEM communication module. You can send your data by SMS or do missed calls from your Arduino to mobile devices... or to another Arduino connected to this module. It is necessary an antenna in order to establish a communication.

Documentation:
Tutorial: basic guide for getting started with the module.
Video-tutorial
Schematic
AT Commands
SAGEM Module Info

Download the Fritzing library to include in your electronic designs here

NOTE: If you are looking for a complete solution to use 3G, GPRS and A-GPS, you can use our 3G/GPRS shield for Arduino (3G + GPS) or our Kit with Audio/Video

NOTE: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote which counts with more than 50 sensors available to use.

Learn More

XBee-PRO 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing. UFL version. It includes a pigtail to use with our 2dBi or 5dBi antennas.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO ZB embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors†. Programmable versions of the XBee-PRO ZB module make customizing ZigBee applications easy, even without wireless design expertise. UFL Version. It includes a pigtail to use with our 2dBi or 5dBi antennas.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing. SMA-RP version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee ZB embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. SMA-RP Version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing. SMA-RP version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO ZB embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors†. Programmable versions of the XBee-PRO ZB module make customizing ZigBee applications easy, even without wireless design expertise. SMA-RP Version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

2 dBi 2,4 GHz SMAM-RP Antenna

Dimension: 5 cm.

Learn More

5 dBi 2,4 GHz SMAM-RP Antenna

Dimension: 17,5 cms.

Learn More

XBee ZB embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. UFL Antenna Module

It includes a pigtail to use with our 2dBi or 5dBi antennas.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing. On-chip antenna version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO 900 embedded RF modules provide extended-range wireless connectivity to end-point devices. Supporting RF line-of-sight distances of up to 6 miles (with high gain antennas), these modules are ideal for extended-range wireless applications requiring low latency and increased data throughput.Only for use in US & Canada. It includes a pigtail to use with our 2dBi or 5dBi antennas.

• No configuration needed for out-of-the-box RF communications
• Common XBee footprint for a variety of RF modules
• Outdoor RF line-of-sight range up to 6 miles (10 km)
• Fast 156 Kbps RF data rate
• Supports sleep modes for increased battery life
• Product datasheet

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

The kit is consisted of transmitter and receiver, popular used for remote control. 

Demo Scheme could be downloaded here.



Learn More

XBee 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing. On-chip antenna version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO 802.15.4 OEM RF modules are embedded solutions providing wireless end-point connectivity to devices. These modules use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking. They are designed for high-throughput applications requiring low latency and predictable communication timing. On-Chip antenna version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee ZB embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. On-Chip Antenna Module

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO ZB embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors†. Programmable versions of the XBee-PRO ZB module make customizing ZigBee applications easy, even without wireless design expertise. On-Chip Antenna Version.

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO 868 modules are long-range embedded RF modules providing end-point device connectivity for European applications. Supporting RF line-of-sight distances up to 80 km, these modules are ideal for challenging wireless environments where RF penetration and transmission distance are critical to the application. Only for use in EUROPE. SMA-RP Antenna Version

• 868 MHz short-range device G3 band for Europe
• No configuration needed for out-of-the-box RF communications
• Common XBee® footprint for a variety of RF modules
• Outdoor RF line-of-sight range up to 80 km
• Simple to use peer-to-peer or point-to-multipoint topology
• Product datasheet

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO 900 embedded RF modules provide extended-range wireless connectivity to end-point devices. Supporting RF line-of-sight distances of up to 6 miles (with high gain antennas), these modules are ideal for extended-range wireless applications requiring low latency and increased data throughput. Only for use in US & Canada.SMA-RP Version.

• No configuration needed for out-of-the-box RF communications
• Common XBee footprint for a variety of RF modules
• Outdoor RF line-of-sight range up to 6 miles (10 km)
• Fast 156 Kbps RF data rate
• Supports sleep modes for increased battery life
• Product datasheet

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More

XBee-PRO 868 modules are long-range embedded RF modules providing end-point device connectivity for European applications. Supporting RF line-of-sight distances up to 80 km, these modules are ideal for challenging wireless environments where RF penetration and transmission distance are critical to the application. Only for use in EUROPE.It includes a ufl to SMA pigtail to use with our 2dBi or 5dBi antennas.

• 868 MHz short-range device G3 band for Europe
• No configuration needed for out-of-the-box RF communications
• Common XBee® footprint for a variety of RF modules
• Outdoor RF line-of-sight range up to 80 km
• Simple to use peer-to-peer or point-to-multipoint topology
• Product datasheet

Note: If you are searching for Wireless Sensor Networks devices (motes) you may be interested in our ready to market sensor platform: Waspmote. You can discover the differences between both platforms in the document: Waspmote vs SquidBee.

Learn More