Search results for 'Male'

RP-SMA male to RP-SMA female adapter.
Lenght: 7cms Learn More

USB female 'Type B' connector in a vertical mounting configuration. The 4 connection pins have 0.1" spacing allowing it to be inserted into development boards and perf boards with mild modification. You can either drill two 80mil holes for the support posts, or cut them off completely.

Documents:

• Dimensional
• Datasheet

Learn More

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards or interface cables and will allow you to use an antenna/cable with an SMA connection.

You should not need this adapter with any of our antennas or dev boards. These adapters are listed only to help SparkFun users that have rare or odd antenna coupling needs. Be sure to check out the SMA connector tutorial here for more information on SMA connectors.

Documents:

• Datasheet

Learn More

USB Type 'A' Male connector. Ideal for making very small USB dongle devices that plug directly into a computer USB port or through a USB AtoA extension cable.

Documents:

• USB Type A Connector Datasheet
• SFE Eagle Library has this part!

Learn More

This is your typical male to male dual RCA cable. Red and white normally indicate left/right audio channels but this cable can also be used for video with mono-audio (like the original Nintendo!).

Dimensions: 12 feet

Learn More

USB Type 'B' Female connector. The 4 connection pins have .1" spacing allowing it to be inserted into development boards and perf boards with mild modification. You can either drill two 80mil holes for the support posts, or cut them off completely.

Documents:

• USB Type B Connector Datasheet
• SFE Eagle Library has this part!

Learn More

This is an inner thread (outer nut) adapter that will connect to any of our wireless boards or interface cables and allow you to use an antenna/cable that has an outer thread configuration.

You should not need this adapter with any of our antennas or dev boards. These adapters are listed only to help SparkFun users that have rare or odd antenna coupling needs. Be sure to check out the SMA connector tutorial here for more information on SMA connectors.

Supported Connections: Any RP-SMA or SMA antenna, cable, or connector that uses an outer thread design. All Spark Fun antennas use an inner thread (outer nut) design.

Learn More

A row of right angle headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Learn More

Quality DB9 Male Header Solder Tail package. 

The Female version is also available.

Learn More

This is a simple two wire cable. Both ends have a 2-pin 0.1" pitch female connector. Dimensions: 150mm length Learn More

Single row of 30-holes, female header with swiss round machined pins. These units have very high quality round pins to accept and retain machine pin headers much better. Can be cut to size with a pair of wire-cutters. Standard .1" spacing. We use them extensively in the Olimex development boards. They mate very well with break away headers.

Documents: 30-Pin Swiss Female Headers

Learn More

Unsoldered iPhone/iPad/iPod Connector, Comes in 7 Pieces. Easy to Assemble.

Documents: Style 1 iPhone/iPad/iPod Connector Datasheet

Learn More

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution. Learn More

These are a longer version of our standard break away headers. The plastic separator can be slid up or down to accommodate your needs. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. It is used on Arduino Ethernet Shield. Learn More

This is a SMD 6 pin right angle male header. We use this header on our LilyPad Main Board.

Pins have 0.1" spacing between rows and between pins.

Documents:

• Datasheet

Learn More

DB9 Female Header Solder Tail package. Learn More

This is an un-soldered male iPhone/iPad/iPod connector. This product comes in three easy-to-assemble pieces. This iPhone/iPad/iPod connector is more compact than the other styles we carry. It's also really similar to what's being shipped with new iPhones and iTouches these days.

Learn More

Simple breakout board for the USB Female Type B Vertical Connector. We primarily designed this board so that you could panel mount a USB connector. Handy when creating those fancy looking enclosures that need a USB port. Breakout board is shipped bare. All four USB pins are broken out.

Documents:

• 
  Schematic
• Dimensional for USB connector
• Eagle Files

Learn More

USB Type 'A' Female SMD connector. For use with any PCB that will be used with a Type A to Type A USB cable. Designed to mount to the UBW32.

Documents:

• Datasheet

Learn More

Description: These 0.1" spaced female headers are perfect for building your own Raspberry Pi add-on modules. These PTH headers are arranged in 2 rows of 13 and mate with the Raspberry Pi GPIO header. For more information, check out the drawing below.

Documents:

• Mechanical Drawing

Learn More

2 pin dual-female jumper wire - 300mm 10 PCs pack) Learn More

This is a splittable 20 pin dual female jumper wire, it is superflexible, can be transformed from 1-20 pin jumper wire. Learn More

Learn More

4 pin 2.54mm to 2.0mm Female jumper wire, 100mm per PC, 5 PC / Pack. Learn More

4 pin dual-female jumper wire - 300mm (5 PCs pack) Learn More

4pin to4 separated pins female jumper wire300mm(5 PCs pack) Learn More

6 pin dual-female jumper wire - 100mm (5 PCs pack) Learn More

6 pin dual-female jumper wire - 300mm (5 PCs pack) Learn More

Learn More

This is a through-hole 6-pin right-angle female header. We use this header on our FTDI Basic Breakout boards, and it connects perfectly with the 6-pin male header on Arduino Pros and LilyPad Main Boards.

Pins are spaced by 0.1".

Documents:

• Datasheet

Learn More

Description: This 6-pin connector and plug set is great when you need to create a robust connection for signal or power. This product consists of two separate parts, the panel-mount jack and the mating plug. The plug has a ring which screws to the panel-mount connector ensuring a solid connection that won't pull off.

The connector uses 6 solder-cup connections for easy wiring. The panel-mount side mounts in a 15.5mm hole with the aid of a lock-washer and nut (both included). The jack uses solder-cup terminals as well and comes apart for easy assembly. It even has a strain relief clamp on the end which clamps down to 5mm for a sturdy connection. Pins are clearly labeled on both jack and connector.

Documents:

• Datasheet
• Product Video

Learn More

Learn More

Type: omnidirectional antenna
Polarisation: vertical
Frequency: 5470-5875 MHz
Impedance: 50Ω
VSWR: ≤1.5:1
Gain: 9 dBi
Connector: N female
Power handling: 20 W
Mount: mounting bracket fits 35-50 mm mast tubes
Diameter: 23/32 mm
Length: 350 mm excl mounting bracket
Weight: 410 g (shipping)
Color: light grey
Other: DC grounded
Designed for IEEE 802.11a.

Learn More

DB9 female header - right angle PCB mount. 0.318" Style.

Documents:

• Datasheet

Learn More

This is a 8-pin female header which is used on Arduino board. Learn More

Single row of 40-holes, female header. Can be cut to size with a pair of wire-cutters. Standard .1" spacing. We use them extensively in the Olimex development boards. They mate very well with break away headers.

Please note: You will probably lose one pin with each cut.

Learn More

A row of right angle male headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Learn More

Learn More

Learn More

Quality DB9 Female Header Solder Tail package. 

The Male version is also available.

Learn More

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive female barrel jack. If you have a power supply with a barrel jack and want to plug it into a breadboard, this might be the simple solution.

Learn More

Description: This barrel jack plug is great for adding a common connector to the end of our wires. This jack is compatible with 5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.

Documents:

• Product Video

Learn More

Learn More

Description: These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief.

This is a 10-Pin male header.

Documents:

• Datasheet

Learn More

Description: These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief.

This is a 6-Pin female header.

Documents:

• Datasheet

Learn More

Description: These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief.

This is a 6-Pin male header.

Documents:

• Datasheet

Learn More

Description: These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief.

This is an 8-Pin female header.

Documents:

• Datasheet

Learn More

Description: These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief.

This is an 8-Pin male header.

Documents:

• Datasheet

Learn More

Unsoldered iPhone/iPad/iPod Connector, Comes in 7 Pieces. Easy to Assemble. Style 2 uses a metalized connector for greater stability and connection retention.

Documents: Style 2 iPhone/iPad/iPod Connector Datasheet

Learn More

Description: This is the female connector found inside the iPod itself. Mates with the v1/v2 iPod connectors listed.

Documents:

• iPod SMD Connector Datasheet
• iPod Pinout

Learn More

Learn More

Learn More

Description: This is a 2-pin female JST connector typically used for low-voltage applications running 10A or less. These come in a bag of 10 female sockets, plus enough pins to connect them all.

• 10 Female Sockets
• 20 Pins

Learn More

This is a 2-pin JST RCY connector typically used for low-voltage applications running 10A or less. They are commonly found in RC vehicles. These come in a bag of 1 male plug, 1 female plug, plus pins to connect them both. The pins crimp to your cable and are inserted into the housing.

• 1 male socket
• 1 female socket
• 4 pins

Documents:

• Datasheet

Learn More

This is a simple two wire cable. One end has a 2 pin female 0.1" pitch connector. Opposite end has 2-pin JST connector.

Dimensions: 130mm

Documents:

• JST connector
• Digikey 455-1734-1-ND (Top Entry)
• Digikey 455-1749-1-ND (Side Entry)



Learn More

Looking to add MIDI to your project? This is a female, 5-pin, right-angle DIN 5/180? connector which will interface with most standard MIDI cables.

The pins are spaced by just about 0.1", making these connectors easy to prototype with. The contacts are rated to 2A @100VAC and 1A @ 24VDC.

Keep an eye out for upcoming MIDI-based products using these connectors!

Documents:

• 
  Datasheet

Learn More

Description: You might have seen these cables used in computers. They are typically used to bring USB connections from a motherboard to the external case, or the rear expansion slots. They have a 0.1" spaced 4-pin header on one end and a USB A connector on the other.

Documents:

• Datasheet

Learn More

Description: These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these standard connectors.

These Female quick-disconnects are about 1/4" wide and can be crimped onto 16-14 AWG wire. Mating connectors can be found in the related items.

Documents:

• Datasheet

Learn More

Description: These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these standard connectors.

These Female quick-disconnects are about 1/5" wide and can be crimped onto 16-14 AWG wire. Mating connectors can be found in the related items.

Documents:

• Datasheet

Learn More

Description: These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these standard connectors.

These Male quick-disconnects are about 1/4" wide and can be crimped onto 22-16 AWG wire. Mating connectors can be found in the related items.

Documents:

• Datasheet

Learn More

Description: These connectors are really useful as power connectors in prototyping or in projects that are repeatedly assembled and disassembled. There are also a variety of buttons and lights that use these standard connectors.

These Male quick-disconnects are about 1/5" wide and can be crimped onto 22-16 AWG wire. Mating connectors can be found in the related items.

Documents:

• Datasheet

Learn More

These 2x5 crimp connectors can be snapped onto 10-wire ribbon cable to make your own cable assemblies and keep your connections organized. Simply press the connector onto your ribbon cable, no soldering required, which makes it easy to add as many mid-cable connectors as you need.

Check the related items below for ribbon cable to go with these connectors.

Note: The price is for one connector.

Documents:

• Datasheet

Learn More

These 2x3 crimp connectors can be snapped onto 6-wire ribbon cable to make your own cable assemblies and keep your connections organized. Simply press the connector onto your ribbon cable, no soldering required, which makes it easy to add as many mid-cable connectors as you need.

Check the related items below for ribbon cable to go with these connectors.

Note: The price is for one connector.

Documents:

• Datasheet

Learn More

This 2x5 crimp connector snaps onto a 10-pin ribbon cable to form a dual-inline connection that can be pushed right into a breadboard.

Documents:

• Datasheet

Learn More

Description: DB9 connectors are a great way to make a tight connection on your project or to plug into existing serial lines. Now you can make your own DB9 cables the easy way with these crimp-on ribbon cable connectors. These work great with our 10-wire ribbon cable, you just need to peel back the one unneeded wire. Matching male connectors are available and can be found in the related items below.

Includes:

• Male DB9 connector body
• Rear cap
• Strain relief cap

Documents:

• Dimensional Drawing

Learn More

Description: DB9 connectors are a great way to make a tight connection on your project or to plug into existing serial lines. Now you can make your own DB9 cables the easy way with these crimp-on ribbon cable connectors. These work great with our 10-wire ribbon cable, you just need to peel back the one unneeded wire. Matching female connectors are available and can be found in the related items below.

Includes:

• Male DB9 connector body
• Rear cap
• Strain relief cap

Documents:

• Dimensional Drawing

Learn More

This is a 12" servo cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Female connector on one end goes to controller and the female connector on the other mates with male pins commonly found on a controller board (such as a UAV controller or the ArduPilot). This cable does not easily connect to servos but connects great with receivers. Wire can also be used as a simple 0.1" jumper cable.

Includes removable plastic shrouds for both ends.

Learn More

This is a 12" servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to controller, female connector mates with servo. Fits all Hitec, Futaba, JR, Multiplex, and Airtronics Z servos. Wire can also be used as a simple 0.1" jumper cable.

Note: These wires have a weird naming convention. Both ends of this wire have what, in most cases, should be called a female connector; but, for these wires, the presence (or lack thereof) of the plastic shroud is what makes an end female or male. If you're looking to plug one end of these wires into a breadboard, you could stick our breakaway male headers into the un-shrouded end to make it a true male connector.

Learn More

Description: These sew-on fabric snaps are the same size used on the LilyPad SimpleSnap boards. You can sew these into your project to allow for easy removal or prototyping. They are 8mm snaps, which is equivalent to a size #1/0 at your local fabric shop.

Includes:

• 15x male snaps
• 15x female snaps

Learn More

These connectors are made from high-temp nylon with gold-plated spring pins or sockets molded in. The shape of the XT60 prevents reverse polarity, and when plugged in the connection is super-solid. Perfect for applications up to and beyond 65A continuous draw. Sold in pairs of 1 male and 1 female connector

Learn More

Learn More

Description: fabrickit is a collection of wearable electronic modules, or bricks, that make it easy to construct simple or complex wearable projects. Bricks connect to each other with a flexible, 3-wire conductive fabric ribbon. The fabrickit-bricks-and-ribbon approach streamlines the construction of wearable projects, making them more reliable, attractive and ready-to-wear.

The fabrickit Snap Bricks are 3-lead connectors that snap together and can be used to make switches. Use this in conjunction with other fabrickit products, listed below.

Note: This is the female connector only, you will need to order a male connector as well for a connecting set.

Note: This product is a collaboration with fabrickit. A portion of each sales goes back to them for product support and continued development.

Documents:

• Schematic
• Eagle Files
• Product Page
• Getting Started Tutorial
• Conductive Ribbon Soldering Tutorial

Learn More

Description: fabrickit is a collection of wearable electronic modules, or bricks, that make it easy to construct simple or complex wearable projects. Bricks connect to each other with a flexible, 3-wire conductive fabric ribbon. The fabrickit-bricks-and-ribbon approach streamlines the construction of wearable projects, making them more reliable, attractive and ready-to-wear.

The fabrickit Snap Bricks are 3-lead connectors that snap together and can be used to make switches. Use this in conjunction with other fabrickit products, listed below.

Note: This is the male connector only, you will need to order a female connector as well for a connecting set.

Note: This product is a collaboration with fabrickit. A portion of each sales goes back to them for product support and continued development.

Documents:

• Schematic
• Eagle Files
• Product Page
• Getting Started Tutorial
• Conductive Ribbon Soldering Tutorial

Learn More

Learn More

Description: This pack of female headers includes two 6-pin headers and two 8-pin headers. This is similar to the header kit that comes with Arduino shields except that the pins are shorter so they don't stack. These are useful for Arduino compatible boards that don't come with headers already installed (like the Arduino Pro).

Includes:

• 2 x 6-Pin Female Headers
• 2 x 8-Pin Female Headers

Learn More

Learn More

Learn More